IBC ton package
Time:2021/11/5 10:44:43views:
Instructions for IBC ton package
1、 Confirmation of chemical compatibility
The user of this package must confirm the chemical composition of the filled liquid and the raw material of the inner container, high-density polyethylene, sealing material and valve [] material before use
Compatibility.
2、 Filling and storage
1. The nominal volume of this container is 1000L.
2. Open the injection port cover before use. Then fill the liquid through the injection port at the top. A reserved capacity must be reserved to prevent the possibility of being heated during transportation
The degree leads to the expansion of the contained liquid, resulting in leakage or permanent deformation of the container. It shall not be used for transportation. The steam pressure at 50 ° C is higher than 110kpa or 55 ° C
For liquids higher than 130kpa, the maximum transportation temperature is 50 ° C and the minimum is - 18 ° C. tighten all seals before handling.
3、 Drainage
1. The container adopts self weight discharge design. When discharging, first open the filling cover on the top to prevent negative pressure in the container.
2. Unscrew the threaded cover of the discharge valve. Tear off the sealing aluminum foil. If the valve connecting pipe is used, please put it in the threaded cover and install the discharge valve together with the gasket
And tighten. If other suitable adapters are used for discharging, fasten the connectors with tools only.
3. Then remove the locking screw on the lower side of the lower valve handle, and then pull the valve handle forward to start discharging.
4. After discharging, please close the valve counterclockwise, install the locking screw, and screw in the closing cover of the discharging valve and the filling cover.
4、 Loading and unloading
The lifting method of the container is bottom lifting, and the top lifting method is not allowed. If a forklift is used, be sure to observe the safety regulations on the use of forklifts
Then.
5、 Loading in vehicle or container
1. When using IBC packaged goods for transportation, please be sure to implement the loading of cargo transport components (ctus) in the supplement to the international maritime dangerous goods code
The provisions of the guide.
2. The maximum canned density of IBC container barrel is about 1.9. When the canned cargo density is less than 1.5, it can be stacked for 2 layers; When the density is greater than 1.5, one layer can be confirmed.
6、 Routine maintenance and inspection
It is strictly prohibited for the valve and inner container to be impacted and collided by external forces. Before refilling, the status of the returned container must be carefully checked to confirm whether there is any
Unsafe factors affecting continued use.
7、 Service life
The storage shelf life of containers is two years from the date of production.
-
Determination of steel drum volume
2021/10/08a. If the user contains liquid, it shall be calculated according to the specific gravity of the product, but enough space shall be reserved for the expansion and crack of the product due to thermal expansion (except for low boiling point products), so as …
-
Determination of internal coating of steel barrel
2021/10/08The user can provide samples of various internal coatings (including no internal coating and iron series phosphating coating) by the steel barrel manufacturer, conduct the compatibility immersion test under similar environmental conditions for storage and…
-
Different materials shall be used for the inner lining roll of the spiral ring of the closed barrel according to the products contained by the user
2021/10/08The user can provide liners of different materials by the steel barrel supplier to conduct the compatibility immersion test under similar environmental conditions for storage and transportation for more than 1 month. After analyzing the swelling deformati…
-
Different materials shall be used for the inner lining roll of the spiral ring of the closed barrel according to the products contained by the user
2021/10/08The user can provide liners of different materials by the steel barrel supplier to conduct the compatibility immersion test under similar environmental conditions for storage and transportation for more than 1 month. After analyzing the swelling deformati…
-
Different materials shall be used for the inner lining roll of the spiral ring of the closed barrel according to the products contained by the user
2021/10/08The user can provide liners of different materials by the steel barrel supplier to conduct the compatibility immersion test under similar environmental conditions for storage and transportation for more than 1 month. After analyzing the swelling deformati…
-
Attention should be paid to the selection of steel plastic composite barrel
2021/10/08a. Because the lining of steel plastic composite barrel is polyethylene, it is not suitable for filling products above 55 ℃, or it needs to be heated above 55 ℃ in use. If so, it is easy to cause damage to the steel drum.b. The steel plastic barrel is l…
